+Ethernet eth0: MAC address 00:00:00:00:54:33 IP: 192.168.0.93/255.255.255.0, Gateway: 0.0.0.0 Default server: 192.168.0.13, DNS server IP: 0.0.0.0 RedBoot(tm) bootstrap and debug environment [ROMRAM] Non-certified release, version v2_0 - built 08:14:43, Aug 22 2006 Platform: Cirrus Logic EDB9302 Board (ARM920T) Rev A Copyright (C) 2000, 2001, 2002, Red Hat, Inc. RAM: 0x00000000-0x02000000, 0x00041e68-0x01fdd000 available FLASH: 0x60000000 - 0x61000000, 128 blocks of 0x00020000 bytes each. RedBoot> RedBoot> fis load ramdisk.gz RedBoot> load -v -r -b 0x80000 -m http /9302/zImagea Raw file loaded 0x00080000-0x0015f2ab, assumed entry at 0x00080000 RedBoot> exec -r 0x800000 -s 0x800000 -c "console=ttyAM root=/dev/ram" Using base address 0x00080000 and length 0x000df2ac Uncompressing Linux............................................................... done, booting the kernel. Linux version 2.6.8.1-crus2.0.2 (ivan@debian) (gcc version 3.4.1) #10 Wed Sep 6 15:44:21 EEST 2006 CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T) CPU: D VIVT write-back cache CPU: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets CPU: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets Machine: edb9302 Memory policy: ECC disabled, Data cache writeback bank 0 start at 0x00000000, length 0x00800000, mapped to 0xc0000000 bank 1 start at 0x01000000, length 0x00800000, mapped to 0xc1000000 bank 2 start at 0x04000000, length 0x00800000, mapped to 0xc4000000 bank 3 start at 0x05000000, length 0x00800000, mapped to 0xc5000000 Built 1 zonelists Kernel command line: console=ttyAM root=/dev/ram PID hash table entries: 512 (order 9: 4096 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 8MB 8MB 8MB 8MB = 32MB total Memory: 22088KB available (1596K code, 415K data, 64K init) Calibrating delay loop... 99.73 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 8192K NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub NetWinder Floating Point Emulator V0.97 (double precision) ttyAM0 at MMIO 0x808c0000 (irq = 52) is a EP93XX ttyAM1 at MMIO 0x808d0000 (irq = 54) is a EP93XX RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize ep93xxusb ep93xxusb0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET: Registered protocol family 1 NET: Registered protocol family 17 RAMDISK: Compressed image found at block 0 usb 1-1: new full speed USB device using address 2 scsi0 : SCSI emulation for USB Mass Storage devices Using anticipatory io scheduler Vendor: Kingston Model: DataTraveler 2.0 Rev: 5.00 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sda: 2013184 512-byte hdwr sectors (1031 MB) sda: assuming Write Enabled sda: assuming drive cache: write through sda: unknown partition table Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 VFS: Mounted root (ext2 filesystem). Freeing init memory: 64K init started: BusyBox v1.00 (2006.01.19-17:26+0000) multi-call binary lo: driver changed get_stats after register eth0: driver changed get_stats after register Please press Enter to activate this console. BusyBox v1.00 (2006.01.19-17:26+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. ~ #